Electrolux
EFS – Dishwashing Systems Platform
Electrolux Professional
Electronic Dishwasher
SERVICE MANUAL
DOC. NO. 5956.446.06
©Copyright 2005 by
Electrolux Professional
P.14/88
8.
OTHER PARAMETERS
dPA
Dishwashing
Parameters
Sym. Parameter
Description
Unit Min
Max
Factory
Default
IPA
Initial Pause before start washing (for ALL cycles)
[s]
0
10
0
dLY
Delay for the 2
nd
wash pump (PW only)
[s]
0
10
3
Pdr
Active a drain phase at the end of washing phase.
[s]
0
40
0
RPA
Duration of pause after rinse cycle (valid for dishwashers with door/hood
lock device) [See par. 9.2 Medical line dishwasher with door/hood lock
device].
[s] 0 60
0
C F
Celsius/Fahrenheit selection
0 = Celsius
1 = Fahrenheit
- 0
1
0
rit
Rinse Temperature Display.
Enable rinse temperature probe (if installed).
0 =
during rinse phase the display shows boiler temperature;
1 =
during rinse phase the display shows rinse temperature;
- 0
1
0
PPL
Pulse Per Litre.
This parameter must be settled in according to flow meter installed.
[p/l] 0 255
0
CdE
Number of wash cycles performable without detergent (only for
dishwashers with external detergent level sensor – par. 9.2.1 Detergent
and rinse aid level sensors activation) [
LES=1
]
- 0
5
5
1LE
Pressure sensor threshold 1 [present up to software version 2.11].
-
0
255
140
1HS
Pressure sensor histeresis 1 [present up to software version 2.11].
-
0
255
50
2LE
Pressure sensor threshold 2 [present up to software version 2.11].
-
0
255
140
2Hs
Pressure sensor histeresis 2 [present up to software version 2.11].
-
0
255
50
Note:
1LE
,
1HS
,
2LE
,
2HS
parameters emulates a two levels pressure switch, keep in mind that value doesn’t correspond to a
physical quantity.
ron
Read Only Parameters
Sym. Parameter
Description
Unit Min Max
Factory
Default
rEL
Main Board Firmware Release
-
-
-
-
rLs
Water softener board software version.
- - - -
CAll
When
CAll
message appears, the parameter value becomes
1
.
After maintenance, to clear
CAll
message, insert
0
.
- - - -
C 8
When
C 8
alarm appears, the machine is frozen and this parameter is
1
.
After maintenance (see alarm codes document), insert 0 to enable the
machine.
- - - -
F21
This alarm appears in case of malfunctioning in the continuous water
softener. To facilitate fault-finding, see par. E "Alarm codes that stop the
machine for models with incorporated continuous water softener".
- - - -
HCP
Communication and HACCP Parameters
Sym. Parameter
Description
Unit Min
Max
Factory
Default
SEr
Serial Device
0 = 8N1
1 = PC connection (DAAS 8E1)
7 = HACCP network (ECAP 8E1+LK485)
(LK485 board is necessary)
9 = Dishwashers with incorporated continuous
water softener
16 = HACCP printer (8N1)
32 = MODEM GSM (DAAS 8N1)
33 = MODEM GSM (DAAS 8E1)
48 = Hyper Terminal (8N1)
- 0
63
1
Adr
Address.
This parameter specifies the address of the appliance into the
‘HACCP_network’.
Works only if ‘HACCP network’ is selected (see above parameter).
- 0
255
1
