manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 82 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 82

82 GEO3.5 MANUAL

CONTINUED

From time to time the software of the GEO3.5 may be updated, resulting in 

changes to the default values for some parameters. For the most up to date 

default values please consult the online version of this manual at 

www.planeteclipse.com
The arrangement of menus and sub menus displayed in the above menu tree 

may not be replicated in your marker due to any software updates that may have 

taken place since printing.

OFF 

Shot gauge off

ON (Default)  

Shot gauge on

CANCEL  

Cancel selection

100-2000  

Shot gauge maximum (reset value) (GAUGE dependant). (Default 140 shots)

Return to Main Menu

00:00 - 60:00  

Countdown game timer start time in minutes. (Default 07:10)

00:00 - 60:00  

Alarm activation time in minutes. (Default 01:00)

BUTTON (Default)  

Pressing the button starts the Game Timer.

TRIGGER  

A trigger pull starts the Game Timer

CANCEL  

Cancel Game Timer start selection

Return to Main Menu

 SHOT COUNT 

 GAME TIMER 

 EXIT 

 GAUGE 

 GAUGE 

 ALARM 

 START 

 GAUGE MAX 

 BACK 

 BACK 

Summary of Contents for GEO3.5























































































Reviews:

No comments