manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 63 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 63

GEO3.5 MANUAL 63

SYMPTOM

POSSIBLE CAUSE

SOLUTION

The GEO3.5 de-gasses very slowly

The body filter is blocked / damaged

Clean the body filter and inspect for damage 

Replace if damaged

The GEO3.5 leaks from the solenoid assembly

Check that the three solenoid gaskets are intact 

and seated in their designated pockets both in and 

around the solenoid manifold

Replace any of the solenoid gaskets if they are 

damaged

GEO3.5 solenoid assembly is over-pressurising

Check the inline regulator output pressure and 

consequent velocity. Adjust accordingly

Strip and clean the SL4 inline regulator. Replacing 

the seals as necessary

Debris on / damage to poppet

Clean / replace the poppet

Damaged GEO3.5 solenoid valve

Replace the GEO3.5 solenoid valve

GEO3.5 leaks down the barrel

Front or rear prop shaft 14 x2 NBR 70 o-rings are 

damaged, dirty or dry

Replace, clean and lubricate 14 x 2 NBR 70 o-rings 

on prop shaft

Internal 017 NBR 70 o-ring and external 020 NBR 70 

o-rings on bolt can are damaged, dry or dirty

Replace, clean and lubricate 017 NBR 70 o-ring and 

020 NBR 70 o-rings on the bolt can

Gas vents quickly down the barrel as soon as the 

GEO3.5 is gassed up

The bolt is stuck in a forward position

Push the bolt backwards

Main prop shaft 014x2 o-ring is damaged or an 

incorrect size

Replace with a new 014x2 size o-ring

The GEO3.5 is chopping or trapping paint

The loader has too high a force feed setting

Adjust the loader to a lower force feed setting

Poor quality paintballs

Use better quality paintballs

The break beam sensor system is switched off

Switch on the break beam sensor system

The bolt is dirty causing the incorrect detection of 

paintballs

Clean the bolt and breach

Summary of Contents for GEO3.5























































































Reviews:

No comments