manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 36 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 36

36  GEO3.5 MANUAL

BASIC TRIGGER FILTER SETUP

95% of trigger bounce problems can be eliminated by utilizing one of the nine fixed DEBOUNCE choices (LEVEL 1-9). 

In attempting to eliminate trigger bounce it is advisable to try the nine fixed DEBOUNCE choices before attempting any ad-

vanced set up of the trigger filters.

ADVANCED TRIGGER FILTER SETUP

In order to optimize the trigger filters it is necessary to have the PULL PT parameter set as high as possible and the RELEASE 

PT parameter set as low as possible:
1.   Select the PULL PT parameter. Observe that the graphical bar rises and falls as the trigger is pulled and released. 

The actual value of the graphical bar is displayed in the top right of the display.

2.    Set the rear stop screw as required, ensuring that the bar is as close to 100% as possible when the trigger is fully 

depressed against the set screw. It is advisable to allow for some extra travel in the trigger pull once the bar has reached 

its maximum value.

3.    Adjust the PULL PT parameter so that when the trigger is fully depressed the bar settles above the indicator on the left 

hand side of the screen (see page 35).

4.   Select the RELEASE PT parameter. Observe that the graphical bar rises and falls as the trigger is pulled and released. 

The actual value of the graphical bar is displayed in top right of the display.

5.    Set the front stop screw as required, ensuring that the bar is as close to 0% as possible when the trigger is fully released 

against the set screw. It is advisable to allow for some extra travel in the trigger release once the bar has reached its 

minimum value.

6.    Adjust the RELEASE PT parameter so that when the trigger is fully released the bar settles beneath the indicator on the left 

hand side of the screen (see page 35).

7.    Set the magnet return strength screw and the spring return strength screw as required, making both the spring tension and 

the return force as strong as possible without compromising the “feel” of the trigger.

HARDWARE MENU 

This menu comprises parameters that control low level functionality of the GEO3.5 electronic hardware. 

Summary of Contents for GEO3.5























































































Reviews:

No comments