manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 37 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 37

GEO3.5 MANUAL  37

TRIGGER PARAMETER 

The GEO3.5 is fitted with a dual trigger pull detection system. 

A non-contact OPTO-Electronic trigger sensor arrangement is 

used to detect trigger movement whilst a micro-switch is used to 

provide a more traditional tactile feedback for the trigger. 

The TRIGGER parameter is used to select which system is used.

The choices available are as follows:
>  OPTO: Select the OPTO sensor for trigger pull detection.
>   SWITCH: Select the micro-switch for trigger pull detection.
>   CANCEL: Cancel editing and leave the parameter 

unchanged.

SOLENOID PARAMETER

This parameter controls the amount of power used by the 

solenoid valve and should normally be left at it’s default ‘LO 

PWR’ setting. Cold weather (sub 0°C/32°F) will cause lubricants 

to thicken and increase stiction in the marker system which 

may cause velocity drop-off and/or shot to shot inconsistency. 

Increasing the solenoid power will often help to eliminate these 

problems, but will cause more drain on the battery. 

The choices available for the parameter are:-
>  LO PWR: Low power solenoid drive.
>  HI PWR: High power solenoid drive.
>   CANCEL: Cancel editing and leave the parameter 

unchanged.

SOUND PARAMETER

The GEO3.5 board is capable of emitting a variety of sounds 

to audibly signal when certain functions have been performed 

including, but not limited to, powering up, powering off, changing 

the BBSS mode and resetting various counters and timers. 

This parameter determines if this feature is switched on or off. 

Switching it on will cause increased drain on the battery.

The choices available for this parameter are:
>  OFF: Sounds switched off.
>  ON: Sounds switched on.
>   CANCEL: Cancel editing and leave the parameter 

unchanged.

TONES PARAMETER

This parameter determines if the GEO3.5 emits a tone each time 

any of the push-buttons on the navigation console are activated. 

As part of the smart menu system the TONES parameter will 

only be shown in the Hardware menu if the SOUND parameter is 

switched ‘ON’.

The choices available for this parameter are:
>  OFF: Tones switched off.
>  ON: Tones switched on.
>   CANCEL: Cancel editing and leave the parameter 

unchanged.

Summary of Contents for GEO3.5























































































Reviews:

No comments