Eclipse GEO3.5 User Manual Download Page 35

Page: 35 / 86

GEO3.5 MANUAL 35

PULL TM PARAMETER

The PULL TM parameter is used to set the minimum amount of time that the trigger must be pulled before it is recognised as

a valid trigger pull. This parameter can be set between 3.0 and 20.0 milliseconds in 0.1ms increments.

RELEASE TM PARAMETER

The RELEASE TM parameter is used to set the minimum amount of time that the trigger must be released before it is

recognised as a valid trigger release. This parameter can be set between 3.0 and 25.0 milliseconds in 0.1ms increments.

PULL PT PARAMETER

The PULL PT parameter is only available if OPTO has been selected in the Hardware menu. PULL PT defines the point at

which the trigger is considered pulled and is adjustable between 51% and 99% in 1% increments.

RELEASE PT PARAMETER

The RELEASE PT parameter is only available if OPTO has been selected in the Hardware menu. RELEASE PT defines the

point at which the trigger is considered released and is adjustable between 1% and 49% in 1% increments.

Summary of Contents for GEO3.5























































































Search results

Summary of Contents for GEO3.5

Reviews:

Eclipse GEO3.5, User Manual, Page: 35 / 86

Search results

Summary of Contents for GEO3.5

Reviews: