manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 21 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 21

GEO3.5 MANUAL  21

STORAGE AND

TRANSPORTATION

CAUTION!

Never carry your Eclipse GEO3.5 un-cased when not on a playing field. 

The non-playing public and law enforcement personnel may not be able 

to distinguish between a paintball marker and a real firearm. For your 

own safety and to protect the image of paintball, always carry the Eclipse 

GEO3.5 (or any other paintball marker) in a suitable marker case such as 

the one in which it was supplied.

WARNING

Your Eclipse GEO3.5 must be clear of all paint and propellant during 

transportation or storage.
Make sure the Eclipse GEO3.5 marker is off.
Remove the barrel from the marker.
Make sure the marker is clean of any paint residue, dirt and moisture.
Store your Eclipse GEO3.5 in a clean, cool, dry place.
Keep your Eclipse GEO3.5 away from any unauthorized and unsafe users.
It may be a good idea to remove the battery when storing your Eclipse GEO3.5 

to prevent unauthorized use.
Protect your Eclipse GEO3.5 from excessive heat during transportation.
When transporting a paintball marker by air, check with the airline regarding their 

policies on transporting paintball equipment as hold luggage before arriving at 

the airport.
Observe and obey all local and national laws concerning the transportation 

of paintball markers. For information concerning any of the laws in your area, 

contact your nearby law enforcement agency.
When shipping the Eclipse GEO3.5 for any reason, Planet Eclipse recommends 

using the case in which the marker was originally supplied to protect the marker 

against rough handling during transport. 

Summary of Contents for GEO3.5























































































Reviews:

No comments