manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 58 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 58

58 GEO3.5 MANUAL

CONTINUED

Lastly inspect and clean the large solenoid gasket, replacing if damaged 

(see figure 25M)

. 

 

Apply a small amount of grease to the outer most groove surrounding the 

solenoid manifold pocket in the GEO3.5 body. Then making sure the top solenoid 

manifold gasket lies flat in the solenoid manifold, insert the solenoid manifold 

back into the GEO3.5 body 

(see figure 25N)

. 

 

Next place the solenoid gasket over the solenoid manifold ensuring that the 

gasket is secure in its groove in the GEO3.5 body

 (see figure 25O)

. Make sure 

that the bottom solenoid manifold gasket is flat in its groove in the solenoid 

manifold. 

 

Place the solenoid valve over the solenoid manifold 

(see figure 25P)

, 

making sure the location holes line up with the threads in the GEO3.5 body 

(see figure 25Q)

. 

 

Replace the retaining screws which hold the solenoid onto the GEO3.5 using 

a 5/64” hex key 

(see figure 25R)

. DO NOT over tighten screws in the solenoid 

assembly. 

 

Maintenance of the solenoid assembly is complete. 

 

 

WARNING!

If you are unsure about performing a maintenance procedure please 

contact your nearest service centre.

WARNING

FIG 25M

FIG 25O

FIG 25Q

FIG 25N

FIG 25P

FIG 25R

Summary of Contents for GEO3.5























































































Reviews:

No comments