manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 22 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 22

22  GEO3.5 MANUAL

THE USER INTERFACE

The GEO3.5 has a simple user interface through which all aspects of its 

electronic control system can be monitored and adjusted by means of the three 

push-buttons and graphical LCD which comprise the navigation console.

THE RUN SCREEN LAYOUT 

The root of the user interface is the run screen which is the screen that is 

displayed most often when the GEO3.5 is on. The run screen

1

 has five display 

functions and the user can scroll through these functions by repeatedly pressing 

the   button on the navigation console.
>  Game Timer
>  Shot Counter
>  Peak Rate of Fire Indicator
>  Actual Rate of Fire Indicator
>  SPLASH (marker logo 

2

)

With the exception of the SPLASH, the run screen is vertically divided with the 

screen function displayed on the left and a series of status icons displayed on 

the right.
The SPLASH run screen will display the marker logo with a flashing / alternating 

backlight. The marker is still able to fire when this screen is displayed. 

1  The layout of the run screen is correct at time of printing. However newer versions of the GEO3.5 

software may have a different layout of the run screen from what is printed in this manual. 

You may find some icons have been added or removed entirely. If you are unsure about any 

icons which do not feature in the manual contact your local dealer/service centre or Planet 

Eclipse directly. 

2  The SPLASH graphic can be modified to display custom graphics with the Eclipse E-Portal 

software sold separately (see page 83 for more information on Eclipse E-Portal).

BREAK BEAM SENSOR 

SYSTEM INDICATOR

USER SELECTABLE 

DISPLAY OPTION
LOCK INDICATOR
BATTERY LEVEL

INDICATOR

TRIGGER DETECTION 

INDICATOR

AUX OUT INDICATOR

SOUND INDICATOR

Summary of Contents for GEO3.5























































































Reviews:

No comments