manualshive.com logo in svg

Eclipse GEO3.5, User Manual, Page: 3 / 86

Share
Download
Eclipse GEO3.5 User Manual Download Page 3

WARNINGS  3

WARNING

ADHERE STRICTLY TO THESE AND ALL OTHER

 

SAFETY INSTRUCTIONS AND GUIDELINES!

WARNING!

•   Use only professional paintball fields where codes of safety are strictly 

enforced.

•   Use compressed air/nitrogen only. Do not use any other compressed gas or 

pressurised liquid including CO2.

•   Always follow instructions, warnings and guidelines given with any first stage 

regulator you use with the GEO3.5.

•  Use 0.68 inch calibre paintballs only.
•   Always measure your marker’s velocity before playing paintball, using a 

suitable chronograph.

•   Never shoot at velocities in excess of 300 feet (91.44 meters) per second, or 

at velocities greater than local or national laws allow.

•   Any installations, modifications or repairs should be carried out by a 

qualified individual at a licensed and insured paintball facility.

This Users Manual is in English.

 

It contains important safety guidelines and 

instructions. Should you be unsure at any stage, 

or unable to understand the contents of this manual 

you must seek expert advice.

Le mode d’emploi est en Anglais. 

Il contient des instructions et mesures de sécurité 

importantes. En cas de doute, ou s’il vous est 

impossible de comprendre le contenu du monde 

d’emploi, demandez conseil à un expert.

Este manual de usuarios (operarios)

 

Usarios está en Inglés.Contiene importantes 

normas de seguridad e instrucciones. Si no está 

seguro de algùn punto o no entiende los contenidos 

de este manual debe consultar con un experto.

Diese Bedienungs - und Benutzeranleitung ist 

in Englisch.

 

Sie enthålt wichtige Sicherheitsrichtlinen und - 

bestimmungen. Solten Sie sich in irgendeiner Weise 

unsicher sein, oder den Inhalte dies Heftes nicht 

verstehen, lassen Sie sich bitte von einen Experten 

beraten.

THIS USER MANUAL MUST ACCOMPANY THE PRODUCT IN THE 

EVENT OF RESALE OR NEW OWNERSHIP. SHOULD YOU BE 

UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE (SEE 

SERVICE CENTRES PAGE 66).

Summary of Contents for GEO3.5























































































Reviews:

No comments