Eclipse GEO3.5 User Manual Download Page 28

Page: 28 / 86

28 GEO3.5 MANUAL

THE MENU SYSTEM

The Main menu contains both editable parameters and sub-menus which contain

editable parameters. Some of these parameters affect the way the GEO3.5

shoots and are tournament locked as standard from the factory.

The Main menu also contains the TURN OFF option. Selecting this option will

immediately turn off the GEO3.5, preventing it from firing.

Parameters followed by a * are part of the Smart Menu System and will only be

displayed depending on your chosen settings. (e.g. The BS ON ROF parameter

will only become available if the ROF CAP parameter is set to on).

1 The layout of the main menu is correct at time of printing. However newer versions of the

GEO3.5 software may have a different layout of the main menu, sub-menus and parameters

from what is printed in this manual. You may find some parameters have been added or removed

entirely. If you are unsure about any parameters which do not feature in the manual contact your

local dealer/service centre or Planet Eclipse directly.

Summary of Contents for GEO3.5























































































Search results

Summary of Contents for GEO3.5

Reviews:

Eclipse GEO3.5, User Manual, Page: 28 / 86

Search results

Summary of Contents for GEO3.5

Reviews: