manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 67

Winder

Service manual H867 Version 00.0 - 08/2013

65

15 Winder

15.1 Position of the winder wheel in long arm machines

Long arm

machines

Long arm machines have the winder in the center of the machine arm. 
The winder wheel is therefore not aligned on the upper toothed belt wheel 
in long arm machines, but rather on the driver wheel in the machine arm.

Correct setting

The distance between the winder wheel and the driver wheel is 0.8 mm.

Cover

• Arm cover (

 Section 

4.4.2 Removing and fitting the arm cover

, 

page 11)

Figure 51: Setting the distance between the winder wheel and driver wheel

                                                                                                                                            

Setting steps

1. Loosen the two setscrews (1) on the driver wheel (2).

2. Move the driver wheel (2) to the right or left such that distance to the 

winder wheel (3) is exactly 0.8 mm.

3. Tighten the two setscrews (1) on the driver wheel (2).

Risk of injury

Switch off the sewing machine before setting the position of the 
winder wheel.

WARNING

2

1

3

(1) - Setscrews
(2) - Driver wheel

(3) - Winder wheel

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands