manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 9

Environmental protection information

Service manual H867 Version 00.0 - 08/2013

7

3 Environmental protection information

3.1 General information on environmental protection

Machines or machine parts that have reached the end of their service life 
must be disposed of correctly and in compliance with the legal require-
ments concerning environmental protection.

Use consumables sparingly and dispose of them correctly and in compli-
ance with the legal requirements concerning environmental protection.

3.2 Layout of environmental protection information

The environmental protection text is surrounded by green bars.

The following symbol indicates the type of environmental protection mea-
sure:

Example of the layout of environmental protection information in 
text form

Reference to correct disposal

Type and source of the danger
Consequences in the event of noncompliance

Measures for avoiding the danger

This is what environmental protection information on correct 
disposal looks like and could lead to environmental damage if 
not complied with.

ENVIRONMENTAL PROTECTION

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands