manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 89

Maintenance work

Service manual H867 Version 00.0 - 08/2013

87

20.2.2 Cleaning the motor fan sieve

The motor fan sieve must be cleaned once a month using a compressed-
air pistol. When very fluffy material is used for sewing, the motor fan sieve 
must be cleaned more frequently.

Figure 72: Cleaning the motor fan sieve

Cleaning steps

1. Remove any sewing dust and thread remains using a compressed-air 

pistol.

Damage to the paintwork due to solvent-based cleaners

Solvent-based cleaners damage the paintwork of the machine. 

Use only solvent-free substances for cleaning the machine.

Attention

Risk of injury

Switch off the machine at the main power switch before clean-
ing the motor fan sieve.
Flying dirt particles can get in the eyes, causing injury.
Hold the compressed-air pistol in such a way that no particles 
fly near persons.

WARNING

2

1

(1) - Table plate

(2) - Motor fan sieve

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands