manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 24

Positioning the toothed belt wheels

22

Service manual H867 Version 00.0 - 08/2013

3. Turn the upper toothed belt wheel (1) such that the setscrews (2) are 

seated completely on the surface (5) of the arm shaft.

Short arm

machines

4.

Additional setting step for short arm machines:

Move the upper toothed belt wheel (1) to the side such that the distance 
to the winder wheel (3) is 0.8 mm.

5. Tighten the setscrews (2).

6. Use the screwdriver to push the toothed belt (4) back again.

7.2 Lower toothed belt wheel

Correct setting

The two setscrews for the lower toothed belt wheel are seated completely 
on the surface of the lower shaft.

The toothed belt runs correctly without running against the retaining ring 
or slipping off.

Cover

• Tilt the upper section backwards 

(

 Section 

4.4.1 Access to the machine bottom section

, page 10)

Risk of crushing

Switch the sewing machine off before you check and set the 
lower toothed belt wheel.

WARNING

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands