manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 80

Setting the safety snap-on coupling

78

Service manual H867 Version 00.0 - 08/2013

18 Setting the safety snap-on coupling

The safety snap-on coupling disengages in the event of the thread jam-
ming and thus prevents the hook from being misadjusted or damaged.

18.1 Attaching the safety snap-on coupling

Correct setting

The four setscrews (1) on the two adjusting rings next to the safety snap-
on coupling (3) must be parallel to one another. After the coupling has dis-
engaged, they are no longer parallel.

Cover

• Tilt the upper section backwards 

(

 Section 

4.4.1 Access to the machine bottom section

, page 10)

Figure 64: Attaching the safety snap-on coupling

Setting steps

1. Turn the left adjusting ring  (2) such that the setscrews  (1) on both adjust-

ing rings are parallel to one another.

The coupling engages.

Risk of crushing

Switch off the sewing machine before you reattach the safety 
snap-on coupling after the thread has jammed.

WARNING

3

2

4

5

6

7

1

(1) - Adjusting ring setscrews
(2) - Left adjusting ring
(3) - Safety snap-on coupling
(4) - Right adjusting ring

(5) - Setting slot
(6) - Marking point
(7) - Coupling screw

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands