manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 23

Positioning the toothed belt wheels

Service manual H867 Version 00.0 - 08/2013

21

7.1 Upper toothed belt wheel

Correct setting

The two setscrews for the upper toothed belt wheel are seated completely 
on the surface.

To be additionally checked in short arm machines:

Short arm

machines

In short arm machines, also the distance between the winder wheel and 
the upper toothed belt wheel must be 0.8 mm.

Cover

• Arm cover 

(

 Section 

4.4.2 Removing and fitting the arm cover

, 

page 11)

Figure 14: Setting the upper toothed belt wheel

Setting steps

1. Using the screwdriver, push the toothed belt (4) as far to the side until 

the two setscrews (2) can be seen.

2. Loosen the setscrews (2).

Risk of crushing

Switch the sewing machine off before you check and set the 
upper toothed belt wheel.

WARNING

3

4

5

2

1

(1) - Upper toothed belt wheel
(2) - Setscrews
(3) - Winder wheel (position for short arm 

machines)

(4) - Toothed belt
(5) - Surface of arm shaft

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands