manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 27

Setting the stitch length adjusting wheels

Service manual H867 Version 00.0 - 08/2013

25

8.1 Setting the upper stitch length adjusting wheel

Correct setting

Upper stitch length adjusting wheel to 0:

No play on the stitch regulator gear.
The plates for the gear are parallel, the frame cannot be moved.

Cover

• Tilt the upper section backwards 

(

 Section 

4.4.1 Access to the machine bottom section

, page 10)

Setting steps

1. Switch off the machine at the main power switch.

The machine switches over to the upper stitch length adjusting 

wheel.

Figure 17: Setting the upper stitch length adjusting wheel - Part 1

2. Hold the upper stitch length adjusting wheel (1) using a star key.

3. Loosen the screw (2).

4. Remove the upper stitch length adjusting wheel (1) from the shaft (5).

5. Carefully turn the shaft (5) to the right using a 10 mm wrench.

Risk of crushing

Switch the sewing machine off before you set the upper 
stitch length adjusting wheel.

WARNING

2

3

5

6

4

1

(1) - Upper stitch length adjusting wheel
(2) - Screw
(3) - Lower stitch length adjusting wheel

(4) - Adjusting mark
(5) - Shaft
(6) - Scale

Machine damage possible if the shaft is turned too strongly.

If you turn the shaft too far to the right, then parts on the stitch regulator 
gear could bend or get stuck.
Turn the shaft carefully and stop as soon as you can feel slight resis-
tance.

ATTENTION

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands