manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 44

Aligning the needle bar linkage

42

Service manual H867 Version 00.0 - 08/2013

Figure 33: Aligning the thread lever sideways

3. Loosen the two setscrews (6) on the arm shaft crank (5).

Important:

Make sure that the setscrews stay on the surface.

4. Move the needle bar linkage (4) sideways such that the needle pierces 

exactly in the center of the needle hole (3) for the feed-dog.

5. Push the two adjusting rings  (2) inwards as far as they will go and tighten 

them.

6. Tighten the setscrews (1) on the two adjusting rings (2).

7. Align the thread lever (7) exactly in the middle of the slot.

8. Tighten the two setscrews (6) on the arm shaft crank (5).

Sequence

Then check the following settings:

•

Loop stroke position 
(

 Section 

11.2 Setting the loop stroke position

, page 47)

•

Distance of the hook to the needle 
(

 Section 

11.1 Setting the hook side clearance

, page 45)

5

6

7

(5) - Arm shaft crank
(6) - Setscrews 

(7) - Thread lever

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands