manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 13

Working basis

Service manual H867 Version 00.0 - 08/2013

11

4.4.2 Removing and fitting the arm cover

Figure 2: Removing and fitting the arm cover

Removing the arm cover

1. Position the left adjusting wheel for the sewing foot stroke (2) to 2.

Important:

You can only remove the arm cover when the adjusting 
wheel is positioned at 2. 

2. Loosen the arm cover screws (1).

3. Hold the arm cover (3) at the adjusting wheels and remove it.

Fitting the arm cover

1. Fit the arm cover (3).

2. Screw the arm cover screws (1) firmly in place.

4.4.3 Removing and fitting the head cover

Figure 3: Removing and fitting the head cover

Removing the head cover

1. Loosen the head cover screws (1).

2. Remove the head cover (2).

1

2

3

3

(1) - Arm cover screws
(2) - Left adjusting wheel for the sewing foot 

stroke
(3) - Arm cover

1

2

2

(1) - Head cover screws

(2) - Head cover

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands