Docomo F-01A, Instruction Manual

Page: 19 / 519

17
Easy Search/Contents/Precautions
Handling precautions
◆ General
・
F-01A is waterproof, however, do not allow water to seep into the handset and do
not allow accessories or optional devices to get wet.
- This FOMA terminal is waterproof to IPX5 and IPX7 standards if the external connection jack
cap is strictly closed as well as the back cover is mounted and locked, however, it is not
completely waterproof. In the rain or with the handset wet, do not remove/insert the battery
pack or open/close the external connection jack cap or the back cover. Seeped water may cause
corrosion inside the terminal. Accessories and optional devices are not waterproof.
Malfunctions deemed to have been caused by water are not covered by the warranty. Since
these conditions are outside the scope of the warranty, a repair, if at all possible, is charged.
・
Clean FOMA terminal with a dry soft cloth (such as a cloth for eyeglasses).
- The display of FOMA terminal may have been applied special coating to improve clearness of
the color LCD. When cleaning FOMA terminal, rubbing it roughly with a dry cloth can scratch
the display. Take care when handling the unit, and clean it with a dry soft cloth (such as a cloth
for eyeglasses). Drops of water or dirt left on the display can cause stains or remove the
coating.
- If FOMA terminal is wiped with alcohol, paint thinner, benzine or detergent, the printing may
disappear or color may fade.
・
Clean the jack occasionally with a dry cotton swab.
- If the jack is dirty, the contact may become poor and the power may shut OFF. A dirty jack
can result in poor charging, so clean it with a dry cloth or cotton swab.
・
Do not place FOMA terminal near an air-conditioner outlet.
- The rapid change in temperature may cause condensation, causing internal corrosion and
malfunction.
・
When using, be careful not to subject excessive force to FOMA terminal or the
battery.
- If FOMA terminal is crammed into a brimming bag or placed in a pocket and sat on, display,
internal PCBs or battery pack may be damaged or malfunction. And, if external devices are
plugged into the external connection jack (earphone/microphone jack), the breakage of the
connector or malfunction may result.
・
Carefully read the separate instructions that come with FOMA terminal, adapter
(including battery charger) and desktop holder.
・
Do not rub or scrape the display with a metal piece etc.
- It may scratch the display, causing malfunction or damage.
・
Do not press the surface of the touch panel strongly or operate it with sharp
objects such as a nail, a ballpoint pen and a pin.
- It may damage the touch panel.
◆ FOMA terminal
・
Avoid extreme temperature.
- Use the FOMA terminal where the ambient temperature ranges between 5 and 40
℃
(for
temperatures of 36
℃
or higher, such as in a room with a bath, limit usage to a short period of
time) and the ambient humidity ranges between 45 and 85%.
・
FOMA terminal may affect land-line phones, TVs or radios in use nearby, so use
it as far as possible from these appliances.
・
Maintain a separate record of the data you saved in your FOMA terminal.
- If the data is deleted, DOCOMO assumes no responsibility for the loss of any data.
・
Do not plug external devices into the external connection jack (earphone/
microphone jack) at a slant, or do not pull it forcibly while it is plugged.
- May cause malfunction or damage.
・
Do not fold FOMA terminal with the strap held inside.
- May cause malfunction or damage.
・
It is normal for FOMA terminal to become warm during use or charging. Continue
to use it.
・
Do not leave FOMA terminal with the camera in areas under strong direct
sunlight.
- May cause discoloring or burn-in of materials.
・
The terminal should normally be used with the external connection jack cap
closed.
- Dust and/or water brought into FOMA terminal cause troubles.
・
Do not use FOMA terminal with the back cover removed.
- It may cause the battery to come off, or may cause a malfunction or damage.
・
Do not put an extremely thick sticker etc. on the display or keypad.
- May cause malfunction.
・
Do not give a hard shock to the fingerprint sensor and take care not to scratch its
surface.
- May not only cause the fingerprint sensor to malfunction, but also disable authentication or
pointing operation.