Digitrax Super Empier Builder, Manual, Page: 103 / 126

Share

Page: 103 / 126

Digitrax Super Empier Builder Manual Download Page 103

25.2 DT400 Option #2

25.2.1 Throttle Default Decoder Operation

Each DT400 can be set up to operate new decoders selected by that DT400as
any decoder status code you choose. New decoders are defined as decoders that
have not been selected in your system. Your DT400 is set to expect to operate
mostly decoders that are 128 speed step capable, so when a new decoder is
selected the DT400 defaults to that status code. If you operate mostly decoders
that are only able to recognize 28 speed steps, you can change this setting.

25.2.2 Tetherless Operation Mode

Each DT400 can be set up with radio capability and/or infrared capability
enabled, all tetherless operation disabled and power save enabled or disabled.
DT400 is shipped with IR only enabled and DT400R is shipped with Radio &
IR enabled

Table V: DT400 Throttle Option #1 Choices
Op#1 Value

(hex)

Ballistic
Tracking &
Typematic
Keys

Key &
Knob
Clicks

Run/Stop
Local/Global

x00

No

Yes

Local

x01 (Default)

Yes

Yes

Local

x04

No

No

Local

x05

Yes

No

Local

x10

No

Yes

Global

x11

Yes

Yes

Global

x14

No

No

Global

x15

Yes

No

Global

102

«
...
101
102
103
104
105
...
»

Summary of Contents for Super Empier Builder































































































































Reviews:

No comments