Dell PowerConnect J-EX4200 Hardware Manual Download Page 36

Page: 36 / 238

Table 10: Status LED on Network Ports in J-EX4200 Switches

State and Description

LCD
Indicator

LED

Indicates the administrative status (enabled or disabled). The status indicators are:

•

Green—Administrative status enabled.

•

Unlit—Administrative status disabled.

LED: ADM

Status

Indicates the duplex mode.

The uplink module ports are always set to full-duplex; therefore, the LED is always green.

The status indicators for network ports on the front panel are:

•

Green—Port is set to full-duplex mode.

•

Unlit—Port is set to half-duplex mode.

LED: DPX

Indicates the PoE status.

PoE is not enabled on uplink module ports; therefore, the LED for those ports is always unlit.

The status indicators for network ports on the front panel are:

•

Green—PoE is enabled on the port.

•

Amber—PoE is enabled on the port, but no power is drawn from the port because of one of the
following:

•

No device that draws power from the port is connected to the port.

•

A device that draws power from the port is connected to the port, but the device is not drawing
any power from the port.

•

Unlit—PoE is not enabled on the port.

LED: POE

Indicates the speed.

The speed indicators for network ports on the front panel are:

•

One blink per second—10 Mbps

•

Two blinks per second—100 Mbps

•

Three blinks per second—1000 Mbps

The speed indicators for network ports on the SFP uplink module are:

•

Green—1000 Mbps

•

Unlit—10/100 Mbps

The speed indicators for network ports on the SFP+ uplink module are:

•

Green—The speed of the transceiver installed in the port is the same as the speed at which the
uplink module port is configured to operate.

•

Unlit—The speed of the transceiver installed in the port is not the same as the speed at which
the uplink module port is configured to operate.

LED: SPD

Documentation

Front Panel of a J-EX4200 Switch on page 6

•

Uplink Modules in J-EX4200 Switches on page 25

•

LCD Panel in J-EX4200 Switches on page 11

Dell PowerConnect J-Series J-EX4200 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-EX4200















































































































































































































































Search results

Summary of Contents for PowerConnect J-EX4200

Reviews:

Brands by name

Popular brands

Dell PowerConnect J-EX4200, Hardware Manual

Search results

Summary of Contents for PowerConnect J-EX4200

Reviews:

Brands by name

Popular brands