Danfoss AK-PC 781A User Manual Download Page 2

Page: 2 / 138

Capacity

controller RS8HE202 © Danfoss 2017-07

AK-PC 781A

Contents

1. Introduction .............................................................................3

Application .................................................................................................. 3
Principles...................................................................................................... 4

2. Design of a controller ..............................................................7

Module survey ........................................................................................... 8
Common data for modules .................................................................10

Preface to design ....................................................................................30

Functions ............................................................................................30
Connections ......................................................................................31
Limitations .........................................................................................31

Design of a compressor and condenser control .........................32

Ordering .....................................................................................................41

3. Mounting and wiring .............................................................43

Mounting ...................................................................................................44

Mounting of analog output module ........................................44
Mounting of extension module on the basic module .......45

Wiring ..........................................................................................................46

4. Configuration and operation ................................................49

Configuration ...........................................................................................50

Start the control ...............................................................................88
Manual capacity control ...............................................................89

5. Regulating functions .............................................................91

Suction group ..........................................................................................92

Controlling sensor selection .......................................................92
Reference ...........................................................................................93
Capacity control of compressors ...............................................94

Oil management............................................................................106

Condenser ...............................................................................................108

Capacity control of condenser .................................................108
Reference for condensing pressure ........................................108
Capacity distribution ...................................................................110

Step regulation ......................................................................................110
Speed regulation ..................................................................................110

Condenser couplings ...................................................................111
Safety functions for condenser ................................................111
EC motor ...........................................................................................111
CO2 transcritical system and heat recovery ........................112

Circuit for heat recovery or hot tap water ....................113
Circuit for recovery for heating.........................................114
Circuits for control of CO2 gas pressure ........................117
Receiver control .....................................................................119
Parallel compression ............................................................120

Summary of Contents for AK-PC 781A











































































































































Search results

Summary of Contents for AK-PC 781A

Reviews:

Danfoss AK-PC 781A, User Manual, Page: 2 / 138

Search results

Summary of Contents for AK-PC 781A

Reviews: