manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 65 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 65

AK-PC 781A 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

65

Setup control of receiver 

pressure

1. Go to Configuration menu

2. Select Receiver control

3. Set regulation values

The settings are shown here in 
the display

3 - Receiver control
Vrec output type
Select the signal type for controlling the gas bypass valve:
- Voltage signal
- Stepper motor signal via AK-XM 208C
- 2 stepper motor signal  for parallel valves
Valve min. OD
Limitation of the CCM valve's degree of closing
Valve max. OD
Limitation of the CCM valve's degree of opening.
Prec set point
Select the set point for the pressure in the receiver
Use ext. ref. offset
A 0-10 V signal must displace the temperature reference.
Max. ext. ref. offset
Reference displacement at max. signal (10 V) 
Kp
Amplification factor
Tn
Integration time
Prec min.
Min. permissible  pressure in the receiver
Prec max.
Max. permissible pressure in the receiver
(Also becomes regulation reference if the compressors are 
stopped with the "External compressor stop" function)
Prec min. limit P-band
P-band under "Prec min" where the ICMTS valve's degree of 
opening is increased
Prec max. limit P-band
P-band over "Prec max" where the ICMTS valve's degree of 
opening is decreased
Use hot gas dump
Select whether hot gas should be supplied if the receiver 
pressure falls too low
Prec hot gas dump
Receiver pressure at which hot gas is turned on 
Prec gas dump diff.
Difference at which hot gas is turned off again
IT comp. state
The signal received from the IT controller can be read here
IT comp. start 
Opening degree for the Vrec valve when the IT compressor 
is to start.
IT comp. delay
The opening degree of the Vrec must be higher during the 
entire delay time before the relay pulls, thereby sending a 
signal to the IT controller.
IT comp. Sgc min.
The temperature limit for operation with IT compressor. Will 
not start when a lower value is detected, regardless of the 
opening degree of the Vrec valve.

Configuration - continued

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments