manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 135 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 135

AK-PC 781A 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

135

Condensor

High Sd temp.

High

High disch. temp. SdA

Safety limit for discharge temperature has been exceeded

High  Pc pressure

High

High pressure Pc

High safety limit for condensing pressure Pc has been exceeded

Pc/S7 Sensor error

High

PcA sensor error

Pressure transmitter signal from Pc is defective

S7A sensor error

Temperature signal for S7 media temperature sensor is defective

Detect blocked air flow

Medium

Air flow reduced cond. A

The intelligent  air flow monitoring of the condenser reports that a 
cleaning is due

Fan/VSD safety

Medium

Fan Alarm 1

Fan  no. X is reported defective via safety input

Fan VSD alarm

Variable speed drive for condenser fans has been cut out on safety

Various alarms

Standby mode

Medium

Control stopped, 
MainSwitch=OFF

The control has been stopped via the setting ”Main switch” = Off or  
the external Main switch is off

Thermostat x – Low 
temp. alarm

Low

Thermostat x - Low alarm

The temperature for thermostat no. x has been below the low alarm 
limit for longer time than set delay

Thermostat x – High 
temp. alarm

Low

Thermostat x - High alarm

The temperature for thermostat no. x has been above the high alarm 
limit for longer time than set delay

Pressostat x – Low pres-
sure alarm

Low

Pressostat x - Low alarm

The pressure for pressostat no. x has been below the low alarm limit 
for longer time than set delay

Pressostat x – alarm limit 
high pressure

Low

Pressostat x - High alarm

The pressure for pressostat no. x has been above the high alarm 
limit for longer time than set delay

Voltage input x – Low 
alarm

Low

Analog input x - Low alarm

The voltage signal has been below the low alarm limit for longer 
time than set delay

Voltage input x – High 
alarm

Low

Analog input x - High alarm

The voltage signal has been above the high alarm limit for longer 
time than set delay

User def. alarm text

Low

Custom alarm x -define text

Alarm on general  alarm input DI x

No flow

High

Flow switch alarm

There is no flow in the heating circuit Check the pump

Boiling alarm

High

Boiling alarm

The temperature in the heat circuit is too high

Receiver alarm

High

Prec...

Alarm from the receiver

External power loss

High

External power loss

Supply is interrupted. A message alert. All other alarms stopped.

Steppervalve

High

Stepper - Vhp, Vrec, PI, Vliq.
Open coil, Shorted output, 
Error, Power failure

Check the supply to the current valve.
In the event of an error or power failure: check the supply to the 
stepper module.

System alarms

The alarm priority can not be altered on system alarms

Control mode

Low

Manual comp. cap. Control A

Compressors capacity control runs i manual mode

Control mode

Low

Manual cond. cap. Control A

Condense capacity control runs i manual mode

Low

Refrigerant A not selected

Refrigerant has not been selected

Refrigerant changed

Low

Refrigerant changed

Refrigerant type has been changed

Medium

Time has not been set

Time has not been set

Medium

System Critical exception

A unrecoverable critical system failure has occurred – exchange the 
controller

Medium

System alarm exception

A minor system failure has occurred – power off controller

Medium

Alarm destination disabled

When this alarm is activated the alarm transmission to the alarm 
receiver has been deactivated.  Check and wait.
When the alarm is cleared the alarm transmission to the alarm 
receiver has been activated again

Medium

Alarm route failure

Alarms can not be transmitted to alarm receiver – check communi-
cation

High

Alarm router full

The internal alarm buffer has an overrun – this might occur if the 
controller can not send the alarms to the alarm receiver. Check com-
munication between controller and system unit.

Medium

Device is restarting

The controller is restarting after flash updating of the software

Medium

Common IO Alarm

There is a communication fault between the controller module and 
the extension modules – the fault must be corrected as soon as 
possible

Manual control

Low

MAN DI……….

The in put in question has been put in manual control mode via the 
AK-ST 500 service tool software

Low

MAN DO………

The output in question has been put in manual control mode via the 
AK-ST 500 service tool software

Low

Man set ....

The output in question has been put in manual control mode via the 
AK-ST 500 service tool software

Low

Man control .....

The output in question has been put in manual control mode via the 
AK-ST 500 service tool software

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments