manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 84 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 84

84 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

AK-PC 781A

7. Move on through all the individual displays for the 

condenser group.  

Change displays with the +- button. Remember the settings at 
the bottom of the pages – the ones that can only be seen via 
the ”Scroll bar”. 

8. Safety limits

9. Go back to the overview and move on to the rest of 

the functions.

10. General functions

When all the functions in overview display 1 have been re-
viewed, it is time to look at the "General functions" in overview 
display 2. Press the + button to access.

The first is the thermostat group

Check the settings.

11. Then the pressure switch group

Check the settings.

12. Proceed with the remaining functions.

13. The controller setup has been completed.

Check of settings - continued

The last page contains safety limits and restart times.

All the defined general functions are shown in overview display 2.
In addition to always being shown in display 2, functions can be 
selected to be shown in display 1. Individual functions can be selected 
for display in display 1 via the "Show in overview display" setting.

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments