Danfoss AK-PC 781A User Manual Download Page 48

Page: 48 / 138

Capacity

controller RS8HE202 © Danfoss 2017-07

AK-PC 781A

2. Connect LON communication network

The installation of the data communication must comply with
the requirements set out in document RC8AC.

3. Connect supply voltage

Is 24 V, and the supply must not be used by other controllers or
devices. The terminals must not be earthed.

4. Follow light-emitting diodes

When the supply voltage is connected the controller will go
through an internal check. The controller will be ready in just
under one minute when the light-emitting diode ”Status” starts
flashing slowly.

5. When there is a network

Set the address and activate the Service Pin.

6. The controller is now ready to be configured.

■

Power

■

Comm

■

DO1

■

Status

■

DO2

■

Service Tool

■

DO3

■

LON

■

DO4

■

I/O extension

■

DO5

■

Alarm

■

DO6

■

DO7

■

Display

■

DO8

■

Service Pin

Internal communication
between the modules:
Quick flash = error
Constantly On = error

Status on output 1-8

Slow flash = OK
Quick flash = answer from gateway
in 10 min. after network
installation
Constantly ON = error
Constantly OFF = error

Flash = active alarm/not cancelled
Constant ON = Active alarm/cancelled

External communication
Communication to AK-CM 102

Network installation

Summary of Contents for AK-PC 781A











































































































































Search results

Summary of Contents for AK-PC 781A

Reviews:

Danfoss AK-PC 781A, User Manual, Page: 48 / 138

Search results

Summary of Contents for AK-PC 781A

Reviews: