manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 64 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 64

64 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

AK-PC 781A

Setup control of high 

pressure

1. Go to Configuration menu

2. Select HP control

3. Set regulation values

The settings are shown here in the 
display

3 - HP control
Vhp output type
Select the signal type for controlling the ICMTS valve.
- Voltage signal (ICMTS must have 0-10 V signal)
- Stepper motor signal via AK-XM 208C
- 2 Stepper motor signals for parallel valves
Extra capacity offset
Adjust how much the pressure shall be increased by when 
the function "Extra  capacity offset" is activated.
Pgc min.
Min. acceptable pressure in the gas cooler
Pgc max.
Max. acceptable pressure in the gas cooler
Advanced settings

Pgc max. limit P-band
P-band under "Pgc max" where the valve's degree of 
opening is increased
dT Subcool
Desired subcooling temperature
Kp
Amplification factor
Tn
Integration time
Valve min. OD
Restriction of the ICMTS valve's degree of closing
Valve max. OD
Restriction of the ICMTS valve's degree of opening
Pgc HR min.
Read the min. acceptable pressure in the high pressure 
circuit during heat recovery
Pgc HR offset
Read the pressure increase during heat recovery
Ramp down bar/min.
Here you may select how quickly the reference must be 
changed after a completed heat recovery
Temp. at 100 bar
Temperature at 100 bar. Here you may define the 
regulation curve during transcritical operation. Set the 
required temperature value. 
V3gc
Indicates whether a gas bypass valve is used on the gas 
cooler.
Bypass low limit 
If the sensor Sgc records a temperature that is lower 
than the selected value, the gas will be routed outside 
of the gas cooler (e.g. startup during very low ambient 
temperatures).
Bypass permitted after
Minimum time during which the gas must be fed 
through the gas cooler before bypass is permitted.

Configuration - continued

Warning
If the regulation is stopped dur-
ing high-pressure regulation, the 
pressure will rise.
The system must be dimen-
sioned to the higher pressure; 
otherwise, there will be a loss of 
charge.

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments