manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 63 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 63

AK-PC 781A 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

63

Configuration - continued

Continued

Control type
Choice of control strategy
P-band: The fan capacity is regulated via P-band control. The 
P band is configured as "Proportional band Xp"
PI-Control: The fan capacity is regulated by the PI controller.
Kp
Amplification factor for P/PI controller
Tn
Integration time for PI controller
Capacity limit at night
Setting of maximum capacity limit during night operations. 
Can be used to limit fan speed at night in order to limit the 
noise level.

The following settings are not available when the refrigerant 
selected is CO2.

Monitor Air flow
Choose whether monitoring is required of the condenser's 
air flow via an intelligent error-detection method.
Monitoring requires the use of a Sc3 outer temperature sen-
sor, which must be fitted by the condenser's air inlet.
FDD setting 
Set error-detection function
Tuning: The controller makes an adjustment to the con-
denser concerned. Note that tuning should only be done 
when the condenser is operating under normal operating 
conditions.
ON: Tuning is completed and monitoring has commenced.
OFF: Monitoring is cut out.
FDD sensitivity
Set the sensitivity of error-detection on the condenser’s air 
flow. Must only be changed by trained staff.
Air flow tuning value
Actual tuning values for air flow.

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments