manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 66 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 66

66 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

AK-PC 781A

Setup control of  heat 

recovery

1. Go to Configuration menu

2. Select heat recovery

3. Define heat recovery circuits

4. Define heat circuit requirement 

for pressure variation

  

Press the +-button to go on to the  

 

next page

In our example, we have selected 
CO2 as the refrigerant. This opens 
for the displayed settings. In our 
example we have both a circuit 
for hot tap water and a circuit for 
heating.

3 -Heat recovery
Heat recovery mode (applies only when the refrigerant 

selected is not CO2). See also page 109.
Choice of method for heat recovery
No: Heat recovery not used
Thermostat: Heat recovery operated from thermostat
Digital input: Heat recovery operated from signal on a 
digital input.
Heat recovery relay
Choose whether an output is required that should be 
activated during heat recovery.
Heat recovery ref
Reference for the condensing pressure, when heat 
recovery is activated.
Heat recovery ramp down
Configure how quickly the reference for the condenser 
pressure should be ramped down to normal level after 
heat recovery. Configure in Kelvin per minute.
Heat recovery cutout
Temperature value where the thermostat cuts-out the 
heat recovery. 
Heat recovery  cutin
Temperature value where the thermostat cuts-out the 
heat recovery. 

Heat recovery circuit (applies only when the refrigerant 

selected is CO2). See also page 112.
Here you select which recovery circuits shall be regu-
lated:
- None
- Circuit for hot tap  water
- Circuit for heating
- Both hot tap water and heating

4 - Heat reclaim type for heating
Here you define how the condensing pressure (HP) shall be 

regulated when the recovery circuit for heating requires 
heat:

- No HP offset (simple control)
- HP offset. Here the controller must receive a voltage sig-

nal. The offset values that apply to the max. value must be 
defined in the heat circuit settings. See next page. 

- Max heat reclaim. Here the controller must receive a volt-

age signal, but the regulation is increased to also control 
the pump, fans and gas cooler bypass.

Configuration - continued

CO

2

HFC

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments