manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 20 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 20

20 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

AK-PC 781A

Extension module AK-XM 204A / AK-XM 204B

AK-XM 204A 

AK-XM 204B

Max. 230 V

AC-1: max. 4 A (ohmic)
AC-15: max. 3 A (Inductive)

Function 
The module contains 8 relay outputs.

Supply voltage
The supply voltage to the module comes from the previous mod-
ule in the row.

AK-XM 204B only
Override of relay
Eight change-over switches at the front make it possible to over-
ride the relay’s function.
Either to position OFF or ON.
In position Auto the controller carries out the control.

Light-emitting diodes
There are two rows with LED’s. They mean:
Left row:

• Voltage supply to the controller
• Communication active with the bottom PC board (red = error)
• Status of outputs DO1 to DO8

Right row: (AK-XM 204B only):

• Override of relays

ON = override
OFF = no override

Fuses
Behind the upper part there is a fuse for each output.

Keep the safety distance!
Low and high voltage 
must not be connected to 
the same output group

AK-XM 204B 
Override of relay

Note
If the changeovers are used to override the compressor operation, 
it is necessary to wire a safety relay into the circuit for oil manage-
ment. Without this safety relay, the controller will fail to stop the 
compressor if it should run out of oil. See Regulating functions.

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments