manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 29 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 29

AK-PC 781A 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

29

Communication module AK-CM 102

Function
The module is a new communication module, meaning the row of 
extension modules can be interrupted.
The module communicates with the regulator via data communi-
cation and forwards information between the controller and the 
connected extension modules.

Connection
Communication module and controller fitted with RJ 45 plug con-
nectors.
Nothing else should be connected to this data communication; a 
maximum of 5 communication modules can be connected to one 
controller. 
The communication module can be used only with controllers of 
the type AK-PC 781A.

Communication cable
One metre of the following is enclosed: 
ANSI/TIA 568 B/C CAT5 UTP cable w/ RJ45 connectors.

Positioning
Max. 30 m from the controller
(The total length of the communication cables is 30 m)

Supply voltage
24 volt AC or DC should be connected to the communication 
module. 
The 24 V can be sourced from the same supply that supplies the 
controller. (The supply for the communication module is galvani-
cally separated from the connected extension modules).
The terminals must not be earthed.
The power consumption is determined by the power consump-
tion of the total number of modules.
The controller strand load must not exceed 32 VA.
Each AK-CM 102 strand load must not exceed 20 VA.

Point
Connection points on the I/O modules should be defined as if the 
modules were an extension of each other.

Address
The address for the first communication module should be set to 
1. Any second module should be set to 2.  A maximum of 5 mod-
ules can be addressed.

Termination
The termination switch on the final communication module 
should be set to ON. 
The controller should permanently be set to = ON.

Warning
Additional modules may only be installed following the installa-
tion of the final module. (Here following module no. 11; see the 
sketch.)
After configuration, the address must not be changed.

Max. 32 VA

Max. 20 VA

Max. 20 VA

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments