Danfoss AK-PC 781A User Manual Download Page 87 | Manualshive

Page: 87 / 138

Danfoss AK-PC 781A User Manual Download Page 87

AK-PC 781A

Capacity

controller RS8HE202 © Danfoss 2017-07

87

First start of control

Check alarms

1. Go to the overview

Press the blue overview button with the compressor and con-
denser at the bottom left of the display.

2. Go to the Alarm list

Press the blue button with the alarm bell at the bottom of the
display.

3. Check active alarms

4. Remove cancelled alarm from the alarm list

Press the red cross to remove cancelled alarms from the alarm
list.

5. Check active alarm again

In our case, we have a series of alarms. We will tidy them up so that we
only have those that are relevant.

In our case an active alarm remains because the control has stopped.
This alarm must be active when control has not started. We are now
ready for the startup of control.

Please note that active plant alarms are automatically cancelled when the
main switch is in pos. OFF.
If active alarms appear when the control is started the reason for these
should be found and remedied.

«
...
85
86
87
88
89
...
»

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments