manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 71 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 71

AK-PC 781A 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

71

Separate thermostats

1. Select thermostats

2. Select actual thermostat

3. Define the required thermostat 

functions

Configuration - continued

In our example we select 
one thermostat function for 
monitoring the plant room 
temperature.

We have subsequently entered a 
name for the function.

In our example, separate 
pressostat functions are not used. 

3 - Thermostats
The general thermostats can be used to monitor the tem-
perature sensors that are used, as well as 4 extra temperature 
sensors. Each thermostat has a separate outlet to control 
external automation.
For each thermostat adjust
• Whether the thermostat should also be shown in overview 
display 1. 
  (The function is always shown in overview display 2) 
• Name
• Which of the sensors is used
Actual temp.
Temperature measurement on the sensor that is attached to 
the thermostat
Actual state
Actual status on the thermostat outlet
Cut out temp.
Cut-out value for the thermostat
Cut in temp.
Cut-in value for the thermostat
High alarm limit
High alarm limit
Alarm delay high
Time delay for high alarm
Alarm text high
Indicate alarm text for the high alarm
Low alarm limit
Low alarm limit
Alarm delay low
Time delay for low alarm
Alarm text low
Indicate alarm text for low alarm

3 - Pressostats
Settings as the thermostats

Separate pressostats

1. Select pressostats

2. Select actual pressostat

3. Define the required pressostat 

functions

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments