manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 76 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 76

76 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

AK-PC 781A

Set alarm priorities

1. Go to Configuration menu

2. Select Alarm priorities

3. Set priorities for Suction group

  

Press the +-button to go on to the next page

4. Set alarm priorities for condenser

Very many functions have an alarm connected. 
Your choice of functions and settings has connected all the relevant 
alarms that are current. They will be shown with text in the three 
pictures.
 All alarms that can occur can be set for a given order of priority:
• ”High” is the most important one
• ”Log only” has lowest priority
• ”Disconnected” gives no action
The interdependence between setting and action can be seen in the 
table.

Setting

Log

Alarm relay selection

Net-

work

AKM-
 dest.

Non

High

Low - High

High

X

X

X

X

1

Medium

X

X

X

2

Low

X

X

X

3

Log only

X

4

Discon-
nected

Configuration - continued

In our example we select the settings shown here in the display

Se also alarm text page 134.

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments