manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 52 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 52

52 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

AK-PC 781A

Configuration - continued

Authorization

1. Go to Configuration menu

Press the orange setup button with the spanner at the bottom 
of the display.

2. Select Authorization

3. Change setting for the user ‘SUPV‘

4. Select user name and access code

5. Carry out a new login with the user name and the 

new access code

To activate the new settings you must carry out a new login to the con-
troller with the new user name and the relevant access code.
You will access the login display by pressing the icon at the top left 
corner of the display.

  

This is where you can select the supervisor for the specific system and a 
corresponding access code for this person.

The controller will utilize the same language that is selected in the 
service tool but only if the controller contains this language. If the 
language is not contained in the controller, the settings and readings 
will be shown in English.

When the controller is supplied it has been set with standard authoriza-
tion for different user interfaces. This setting should be changed and 
adapted to the plant. The changes can be made now or later.

You will use this button again and again whenever you want to get to 
this display.
On the left-hand side are all the functions not shown yet. There will be 
more here the further into the setup we go.

Mark the line with the user name SUPV.
Press the button Change

Press the line Authorization to get to the user setup display.

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments