manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 110 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 110

110 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

AK-PC 781A

Step regulation

Cut-ins and cutouts are carried out sequentially. The last cut-in 
unit will be cut out first.

Speed regulation

When an analog output is used the fans can be speed regulated, 
e.g. with a frequency converter type VLT or a EC motor.

Joint speed regulation
The analog output voltage is connected to the speed regulation. 
All fans will now be regulated from 0 to max. capacity. If an ON/
OFF signal is required for the frequency converter, so that the fans 
can be stopped completely, a relay output can be defined.

The controller starts the frequency converter when the capacity 
requirement corresponds to the set starting speed. The controller 
stops the frequency converter when the capacity requirement 
becomes lower than the set minimum speed.

Start
Min.

Speed regu step regulation

The controller starts the frequency converter and the first fan 
when the capacity requirement corresponds to the set starting 
speed.
The controller cuts in several fans step by step as the capacity 
requirement grows and then adapts the speed to the new 
situation.
The controller cuts out fans when the capacity requirement 
becomes lower than the set minimum speed.

In the configuration of the controller’s outputs it will be the output “FanA1”” that will start and 
stop the frequency converter.

Speed regulation of first fan + step regulation of the rest

The controller starts the frequency converter and increases the 
speed of the first fan.
If additional capacity is required, the next fan cuts in at the same 
time as the first fan switches to minimum speed. From here, the 
first fan can increase speed again, etc.

Start
Min.

Capacity distribution

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments