manualshive.com logo in svg

Danfoss AK-PC 781A, User Manual, Page: 73 / 138

Share
Download
Danfoss AK-PC 781A User Manual Download Page 73

AK-PC 781A 

Capacity 

controller RS8HE202 © Danfoss 2017-07 

73

Configuration - continued

1. Select PI functions

2. Select actual PI-function

3. 

Define the required names 

and values attached to the 

function

Separate PI functions

In our example we do not use 
this function, so the display 
has been included for your 
information only.

3 - General PI Control
The function can be used for optional regulation.
Adjust for each regulation 
• Show on overview
• Name 
• Quick settings

Here is a list of suggestions for PI regulations:

• Control mode: Off, Manual or Auto
• Control type: P or PI
• External DI ctrl: Adjusted to On if there is an external switch 

that can start/stop the regulation.

• Input type: Choose which signal the regulation shall receive: 

Temperature, pressure, pressure converted to temperature,

, voltage signal, Tc, Pc, Ss, Sd etc.
• Reference: Either fixed or signal for the variable reference:: 

Choose between: : Non, temperature, pressure, pressure 
converted to temperature,  voltage signal, Tc, Pc, Ss, DI etc..

• Setpoint: If fixed reference is choosen
• Reading the total reference
• Output. Here you select the outlet function (PWM = pulse 

width modulated (fx AKV valve)), Stepper signal for a step-
per motor or voltage signal.

• Alarm mode: Choose whether an alarm shall be attached to 

the function. If it is set to ON, alarm texts and alarm limits 
can be entered.

• Advanced ctrl. settings: 

• Ref. X1, Y1 and X2,Y2: Points that define and limit the 

variable reference

• PWM period time: Period during which the signal has 

been on and off.

• Kp: Amplification factor
• Tn: Integration time
• Filter for reference: Duration for smooth changes to the 

reference

• Max. error:  Maximum permissible fault signal at which the 

integrator remains in the regulation

• Min. control output: Lowest permitted output signal
• Max. control output: Maximum permitted output signal
• Start up time: Time at startup at which the output signal is 

force-controlled

• Startup output: The output signal size at the startup time.
• Stop output signal. Size of the output signal when regula-
tion is off.

Summary of Contents for AK-PC 781A











































































































































Reviews:

No comments