manualshive.com logo in svg

Daktronics ALL SPORT 5500 SERIES, Operation Manual, Page: 7 / 108

Share
Download
Daktronics ALL SPORT 5500 SERIES Operation Manual Download Page 7

Introduction

1

1  Introduction

This manual explains the operation of All Sport

®

 5500 series control consoles. For 

additional information regarding the safety, installation, operation, or service of this 

system, refer to the telephone numbers listed in 

Daktronics Exchange and Repair & Return 

Programs (p� 2)

. 

Important Safeguards

• 

Read and understand all instructions, both general and for specific sports.

• 

Always turn off and/or unplug the control equipment when it is not in use� Never yank 

the power cord to pull the plug from the outlet� Grasp the plug and pull to disconnect�

• 

Do not drop the control console or allow it to get wet�

• 

This device shall not be exposed to dripping or splashing, and no objects filled with 

liquid shall be placed upon it�

WARNING! To reduce the risk of fire or electric shock, do not expose this device to 

rain or moisture�

• 

Console may include internal battery backup, or external battery pack�
CAUTION! DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED�  

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE�

WARNING! Do not expose batteries to excessive heat, such as direct sunlight or fire.

• 

Do not let the power cord touch hot surfaces or hang over the edge of a table that 

would damage or cut the cord�

• 

If an extension cord is necessary, use a three-pronged, polarized cord� Arrange the 

cord with care so that it will not be tripped over or pulled out�

• 

Before using an extension cord, inspect the cable thoroughly and verify its 

compliance with the local electric codes�

• 

Do not disassemble control equipment or electronic controls of the display; failure to 

follow this safeguard will make the warranty null and void�

• 

Inspect console for shipping damage such as rattles and dents, and verify that all 

equipment is included as itemized on the packing slip� Immediately report any 

problems to Daktronics; save all packing materials if exchange is necessary�

All Sport consoles receive external power through a standard 8’ (2.44 m) long three-

pronged power cord plugged into a 120 VAC grounded outlet. The outlet shall be 

installed near the console and easily accessible. Contact Daktronics for information on 

running an All Sport console via optional battery power pack. 

Note: 

The console features an internal time delay 1/8 amp, 250 V fuse. In the unlikely 

event the fuse needs to be replaced, contact Daktronics Customer Service.

Summary of Contents for ALL SPORT 5500 SERIES













































































































Reviews:

No comments