Dahua HCVR82**A-S3 Series User Manual Download

Page: 200 / 381

188

4.16.5 RAID

Note

RAID function is for some series product only.

The RAID (redundant array of independent disks) management can compost the independent HDDs

together to provide larger space as the logic HDD. It can enhance system I/O performance, data usage

and data security.

Right now system supports RAID0/RAID1/RAID5/RAID10.

RAID Type

HDD Amount

RAID0

At least 2 HDDs

RAID1

Only 2 HDDs

RAID5

At least 3 HDDs. Usually we recommend 4 to 6 HDDs.

RAID10

At least 4 HDDs. The amount shall be even number.

4.16.5.1 RAID Config

The RAID configuration interface is shown as in Figure 4-188. In this interface, you can set RAID type

and settings.



Create manually: It is to create RAID manually. Please select RAID type first and then follow the

prompts to set HDD amount. Click Create Manually button, system pops up dialogue box to warning

you it is going to clear all data. Click OK button to complete the operation.



Create RAID: Click it to automatically create RAID5.

For create RAID function, you can select the physical HDD that does not included in the RAID group or

the created disk array to create a RAID5. You can refer to the following situations:



There is no RAID, no hotspare disk: System directly creates the RAID5 and creates one hotspare

disk at the same time.



There is no RAID, but there is a hotspare disk: System creates the RAID5 only. It uses previous

hotspare disk.



There is RAID: System cancel the previous RAID setup and then create the new RAID5. System

creates the hotspare disk if there is no one. System uses previous hotspare disk if there is hotspare

disk available.



The background will format the virtual disk.

Summary of Contents for HCVR82**A-S3 Series






























































































































































































































































































































































































Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Related manuals for HCVR82**A-S3 Series

Brands by name

Popular brands

Dahua HCVR82**A-S3 Series, User Manual

Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Related manuals for HCVR82**A-S3 Series

Brands by name

Popular brands