Dahua HCVR82**A-S3 Series User Manual Download Page 38

Page: 38 / 381

Usually we do not recommend the HDD for the PC. You can refer to the Appendix for recommended HDD

brand.

Please follow the instructions listed below to install hard disk.

3.3.2.1 The 1U Series

The 1U series includes HCR82XXA- -S3.

This series DVR has two SATA HDDs.

①

Loosen the screws of the upper

cover and side panel. Remove

the cover.

②

Fix four screws in the HDD

(Turn just three rounds).

③

Place the HDD in accordance

with the four holes in the bottom.

④

Turn the device upside down and

then turn the screws in firmly.

⑤

Connect the HDD cable and

power cable.

⑥

Put the cover in accordance

with the clip and then place the

upper cover back. Secure the

screws in the rear panel and the

side panel.

3.3.2.2 The 1.5U Series

The 1.5U series includes HCVR84XXL-S3.

This series DVR max has four SATA HDDs. Please use HDD of 7200rpm or higher.

○

Loosen the screws of the

upper cover. Remove the

○

Line up the HDD to the

four

holes

the

HDD

○

Connect the one end of the HDD

cable to the HDD.

Summary of Contents for HCVR82**A-S3 Series






























































































































































































































































































































































































Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Brands by name

Popular brands

Dahua HCVR82**A-S3 Series, User Manual

Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Brands by name

Popular brands