Dahua HCVR82**A-S3 Series User Manual Download Page 30

Page: 30 / 381

Icon

Name

Note

T+

、

T-

、

R+

、

R-

Four-cable full-duplex

485 port.

T+, T-: Send out cable.

R+, R-: Input cable.

CTRL 12V

Control power output

Control power output of the 6

alarm

output channel.



When there is an alarm output, close

the power output.



When the alarm is cancelled, open

the power output.

GND

Ground

eSATA

eSATA port

External SATA port. It can connect to the

device of the SATA port.

USB port

USB port. Connect to mouse, USB

storage device, USB burner and etc.

HDMI1

High Definition Media

Interface 1

High definition audio and video signal

output port. It outputs the same video

source as VGA. It supports 4K resolution

output and supports mouse operation and

control.

Please note when the HDMI output

resolution is 4K, the VGA output stops.

HDMI2

High Definition Media

Interface 2

High definition audio and video signal

output port. It max supports 1080P

resolution. Its video source can be

different from the HDMI1/VGA. It supports

digital channel output.

RS-232

RS-232 debug COM.

It is for general COM debug to configure

IP address or transfer transparent COM

data.

VGA

VGA video output

VGA video output port. Output analog

video signal. It can connect to the monitor

to view analog video.

Network port

1000M Ethernet port

VIDEO IN

Video input port

Connect to analog camera to input video

signal.

Power switch

Power on/off button.

Power socket

Power input port

GND

Ground

2.3

Connection Sample

Summary of Contents for HCVR82**A-S3 Series






























































































































































































































































































































































































Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Brands by name

Popular brands

Dahua HCVR82**A-S3 Series, User Manual

Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Brands by name

Popular brands