Dahua HCVR82**A-S3 Series User Manual Download Page 39

Page: 39 / 381

cover.

bracket. Use four screws to

fix HDD.

○

Connect the other end of

the HDD cable to the

mainboard.

○

Connect the power cable

to the HDD.

○

Put the cover back and fix the

screws to secure firmly.

3.3.2.3 The general 2U Series

The 2U series includes HCVR88XXS-S3.

This series DVR max supports 8 SATA HDDs. Please use HDD of 7200rpm or higher.

①

Loosen the screws of the

upper cover and side panel.

Remove the cover.

②

Fix

the

HDD(s) on

the

bracket. Remove the top

bracket if you want to install

HDD to the bottom bracket.

③

Connect the one end of the HDD

cable to the HDD.

④

Connect the other end of the

HDD cable to the mainboard.

⑤

Connect the power cable to the

HDD.

⑥

Put the cover back and fix the

screws to secure firmly.

Important:

If the HDD amount is less than four, you do not need to install the HDD bracket.

When there is a bracket, please make sure the installation direction of HDDs is the same.

3.3.2.4 The Removable Front Panel 2U Series

Summary of Contents for HCVR82**A-S3 Series






























































































































































































































































































































































































Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Brands by name

Popular brands

Dahua HCVR82**A-S3 Series, User Manual

Search results

Summary of Contents for HCVR82**A-S3 Series

Reviews:

Brands by name

Popular brands