Crowcon I-Test User'S Operation Manual Download

Page: 15 / 125

2. Operating I-Test

This section details how to operate I-Test to perform the desired testing after I-Test has been fully

configured via I-Test Manager (see

page 25

) or via I-Test Front panel Keypad (see

page 90

Ensure I-Test is installed correctly and that the test gas cylinder is attached as detailed on

page 12

Before operating the I-Test it must be configured via I-Test Manager PC Application and

must then be disconnected from the PC USB connection. If I-Test is not disconnected

from the PC it will not operate.

Before a test can be undertaken ensure the I-Test display screen is showing the home

screen. If the home screen is not shown the configured test will not be initiated.

Ensure the test gas cylinder connected to the inlet, has the same gas mix and

concentration as configured in the I-Test (see

page 40

page 94

When manufactured I-Test is configured with a default gas cylinder and a default expiry

date. This expiry date must be changed to that of the actual cylinder to be attached or

I-Test will not function correctly as it will report that the cylinder has expired.

To ensure accurate bump testing and calibration the purge inlet MUST be connected to

fresh air.

When I-Test is initially powered it will perform a purge cycle for approximately 30

seconds, before I-Test can be used.

2.1 Gas Monitor Testing Overview

Once I-Test has been configured to carry out a test or a sequence of tests, proceed as follows:

Ensure the I-Test is either fully charged and/or connected to a suitable power source (see

page 14

Ensure the I-Test is NOT connected to the PC via the USB socket.

Connect the required gas cylinder to the appropriate inlets (see

page 12

Ensure the purge inlet is connected to fresh air.

Ensure a suitable length of pipe that vents to outside air is connected to the exhaust outlet.

Turn the gas monitor on and wait for it to finish its start up routine.

Turn on I-Test and wait for the start up purge sequence to complete

Insert the gas monitor into I-Test (see

page 16

The configured test or test sequence will automatically be performed and I-Test will indicate the

success or failure of the test (see

page 18

Contents

Exit

Unpacking

Set-up

Operating I-Test

I-Test

Manager

Configuring

I-Test

Warranty

Overview

Contacts

Appendices

Troubleshooting

Specification

Summary of Contents for I-Test






























































































































Search results

Summary of Contents for I-Test

Reviews:

Related manuals for I-Test

Brands by name

Popular brands

Crowcon I-Test, User'S Operation Manual

Search results

Summary of Contents for I-Test

Reviews:

Related manuals for I-Test

Brands by name

Popular brands