Page 43
(P39E) sets the length of the pulse .
STAY MODE ARM PULSE to OUTPUT
STAY MODE ARM PULSE to OUTPUT -
P55E 1-32E (1 = Area 1, 32 = Area 32)
Value = 01-32 for Outputs 1-32
Option 01 = Output 1 - Option 32 = Output 32
Sometimes it is necessary to have a single pulse to indicate that Stay Mode is Armed. This could be used to start a
video recorder or similar device. Each time an Area Stay Mode is armed, a single pulse will be applied to the output.
The Pulse time (P39E) sets the length of the pulse .
DISARM PULSE to OUTPUT
DISARM PULSE to OUTPUT -
P56E 1-32E (1 = Area 1, 32 = Area 32)
Value = 01-32 for Outputs 1-32
Option 01 = Output 1 - Option 32 = Output 32
Sometimes it is necessary to have a single pulse to indicate a Disarm state. This could be used to stop a video
recorder or similar device. Each time an Area is disarmed, a single pulse will be applied to the output. The Pulse time
(P39E) sets the length of the pulse.
STAY MODE DISARM PULSE to OUTPUT
STAY MODE DISARM PULSE to OUTPUT -
P57E 1-32E (1 = Area 1, 32 = Area 32)
Value = 01-32 for Outputs 1-32
Option 01 = Output 1 - Option 32 = Output 32
Sometimes it is necessary to have a single pulse to indicate a Disarm of Stay Mode. This could be used to stop a
video recorder or similar device. Each time an Area Stay Mode is disarmed, a single pulse will be applied to the
output. The Pulse time (P39E) sets the length of the pulse.
ARMED EXIT DELAY BEEPS TO KEYPAD
ARMED EXIT DELAY BEEPS TO KEYPAD -
P58E 1-32E (1 = Area 1, 32 = Area 32)
Value = 01-32 for Keypads 1-32
Option 01 = Keypad 1 - Option 32 = Keypad 32
When an Area is Armed it is useful to have the exit delay beeps occurring at the keypad to warn the User to exit the
premises without delay. If the option is on at this address, that keypad will beep out the exit delay. The exit beeps
occur at one second intervals until the last 5 seconds at which time they change to 1/2 second intervals to act as a
warning that the delay is about to expire. Also if Arm on Time-zone or no activity is enabled the Pre-alert (P4072E)
arming beeps will beep the keypad if this option is turned on.
STAY MODE EXIT DELAY BEEPS TO KEYPAD
STAY MODE EXIT DELAY BEEPS TO KEYPAD -
P59E 1-32E (1 = Area 1, 32 = Area 32)
Value = 01-32 for Keypads 1-32
Option 01 = Keypad 1 - Option 32 = Keypad 32
When an Area is Armed in Stay Mode it is useful to have the exit delay beeps occurring at the keypad to warn the
User to exit the premises without delay. If the option is on at this address, that keypad will beep out the exit delay.
This option may be turned off for Stay Mode to make the keypad silent when arming at night time. The exit beeps
occur at one second intervals until the last 5 seconds at which time they change to 1/2 second intervals to act as a
warning that the delay is about to expire. When arming Stay Mode the exit and entry delays can be cancelled by
pressing the <ENTER> button following arming of Stay Mode. The next time Stay Mode is armed, if the <ENTER>
button is not pressed, all programmed exit and entry delays will apply.
ARMED EXIT DELAY TIME
ARMED EXIT DELAY TIME -
P60E 1-32E (1 = Area 1, 32 = Area 32) (Value 0-255 Seconds)
Each Area can have their own exit delay time. The delay can be programmed from 1-255 seconds in one second
increments. If the exit delay is set to “0” the panel will be instantly armed.
