Cosen AH-250H Instruction Manual Download Page 88

Page: 88 / 134

SYSTEMS TROUBLE SHOOTING

Section 9

9-3

9.4 MOTOR TROUBLES AND SOLUTIONS

TROUBLE

PROBABLE CAUSE

SUGGESTED REMEDY

Motor will not start Magnetic switch open, or

protector open.

Reset protector by pushing red button (inside
electric box. )

Low voltage

Check power line for proper voltage.

Open circuit in motor or loose
connections.

Inspect all lead terminations on motor for loose
or open connections.

Short circuit in line, cord or
plug.

Inspect line, cord and plug for damaged
insulation and shorted wire.

Motor will not start,
fuse or circuit
breakers “blow”.

Short circuit in motor or loose
connections

Inspect all lead terminations on motor for loose
or shorted terminals or worn insulation on wires.

Incorrect fuses or circuit
breakers in power line.

Install correct fuses or circuit breakers.

Motor fail to develop
full power. (Power
output of motor
decreases rapidly
w/decrease in
voltage at motor
terminals.)

Power line overloaded with
lights, appliances and other
motors.

Reduce the load on the power line.

Undersize wires or circuit too
long.

Increase wire sizes, or reduce length of wiring

General overloading of power
company‘s facilities.

Request a voltage check from the power
company

Motor overloaded.

Reduce load on motor

Motor overheat

Air circulation through the
motor restricted.

Clean out motor to provide normal air circulation
through motor.

Motor stalls
(Resulting in blown
fuses or tripped
circuit breakers )

Short circuit in motor or loose
connections.

Inspect terminals in motor for loose or shorted
terminals or worn insulation on lead wires.

Low voltage

Correct the low line voltage conditions.

Incorrect fuses or circuit
breakers in power line.

Install correct fuses circuit breakers.

Motor overloaded

Reduce motor load.

Frequent opening of
fuses or circuit
breakers.

Motor overloaded

Reduce motor load

Incorrect fuses or circuit
breakers.

Install correct fuses or circuit breakers.

9.5 BLADE TROUBLES AND SOLUTIONS

Page 88

Instruction Manual for AH-250H (B040)

04/12/2014

Summary of Contents for AH-250H







































































































































Search results

Summary of Contents for AH-250H

Reviews:

Related manuals for AH-250H

Brands by name

Popular brands

Cosen AH-250H, Instruction Manual

Search results

Summary of Contents for AH-250H

Reviews:

Related manuals for AH-250H

Brands by name

Popular brands