Cosen AH-250H Instruction Manual Download Page 32

Page: 32 / 134

MOVING AND INSTALLATION

Section 3

3-9

Installing Fire Control Device

Install a fire extinguisher or other fire control device in the shop to provide safety.

3.4 WORKING CONDITIONS

For safety in operating working, we recommend the following:

A well lighted work site.

To prevent operator from slipping, keep floor dry.

Keep dust from other machines away from electrical control facilities.

Except operator, please do not anyone or anything near your machine for safety.

3.5 RESHIPMENT PROCEDURE

We recommend you do the procedures as follows:

Turn off the power.

Fix the saw head.

Pack machine with plastic bag or soft paper to protecting it from dust.

Pack your machine (with bracket) carefully, and use a crane or forklift to raise it. If a
crane is used to lift the machine, ensure that the lifting cable is properly attached to the
machine.

Do not forget to reship with equipment furnished, shock absorption pads and operating

manual

0 220 415 440 380

0 100 110

Page 32

Instruction Manual for AH-250H (B040)

04/12/2014

Summary of Contents for AH-250H







































































































































Search results

Summary of Contents for AH-250H

Reviews:

Related manuals for AH-250H

Brands by name

Popular brands

Cosen AH-250H, Instruction Manual

Search results

Summary of Contents for AH-250H

Reviews:

Related manuals for AH-250H

Brands by name

Popular brands