Cosen AH-250H Instruction Manual Download Page 2

Page: 2 / 134

Printed in Taiwan

NOTICE:

Please read this instruction manual carefully to obtain a

thorough knowledge of installation, operation and maintenance. Please

remember the following: Correctly operate the machine as described in

the manual to prevent accident. Do not operate the machine by guesswork.

We suggest you always keep manual at hand and refer to it whenever you

are not sure of how to perform any procedures for AH-250H.

TECHNICAL ADVICE/ SPARE PARTS

Please contact the COSEN-representative in your local area in case you need any

technical advice or if you want to order spare parts.

Instruction Manual:

AH-250H Automatic Horizontal Bandsaw

Ver. 1—Date : 09/18/1998

Ver. 2 -- Date : 07/01/2003

VER.3 –Date :12/01/2010

1995 by COSEN CO., LTD./ R&D DIVISION.

110 Ching-Fu Street Hsin-Chu 300, Taiwan, R.O.C.

Tel: 886-3-5332143~5 Fax: 886-3-5348324

No part of this publication may be photocopied or otherwise reproduced without the prior written

permission of COSEN CO., LTD.

Page 2

Instruction Manual for AH-250H (B040)

04/12/2014

Summary of Contents for AH-250H







































































































































Search results

Summary of Contents for AH-250H

Reviews:

Related manuals for AH-250H

Brands by name

Popular brands

Cosen AH-250H, Instruction Manual

Search results

Summary of Contents for AH-250H

Reviews:

Related manuals for AH-250H

Brands by name

Popular brands