Comtech EF Data TRP1000-OD Installation And Operation Manual Download Page 58

Page: 58 / 104

TRP1000-4450 Troposcatter C-Band Outdoor Amplifier

Revision 0

Ethernet-based Remote Product Management

4–14

MN-TRP1000-OD

Trap Version:

Use the drop-down list to select the SNMP Trap Version as

SNMPv1

SNMPv2

For details pertaining to the remaining configuration parameters available on this page, see

Section

6.3 SNMP INTERFACE

Click [

Submit SNMP]

to save. If it is desired to revert back to the previously assigned SNMP

designations, click

[Reset]

instead.

4.5.4.3

Config (TRP1000-4450 Configuration) Pages

Select the

Amplifier

Utility

hyperlink to continue.

4.5.4.3.1

Config | Amplifier

Figure 4-5. Config | Amplifier Page

Use this page to configure the communications, operations, and alarms/faults handling for the
amplifier.

To update the page to the current amplifier configuration: Click

[Refresh]

Serial

Remote Address

– Enter a valid physical remote address from

0001

9999

Baud Rate

– Use the drop-down list to select the operating baud rate as

2400

4800

9600

19200

, or

38400

baud

Data Bits - Parity - Stop Bits

– Use the drop-down list to select the data bits, parity, andstop

bits as

8-N-1

7-E-2

, or

7-O-2

. Default is

8-N-1

Click

[Save Changes]

to save.

Summary of Contents for TRP1000-OD









































































































Search results

Summary of Contents for TRP1000-OD

Reviews:

Related manuals for TRP1000-OD

Brands by name

Popular brands

Comtech EF Data TRP1000-OD, Installation And Operation Manual

Search results

Summary of Contents for TRP1000-OD

Reviews:

Related manuals for TRP1000-OD

Brands by name

Popular brands